Guillows Arrow RC CONVERSION

jonathanmanopla · Post by **jonathanmanopla** » Fri Jul 12, 2013 11:18 am

SOMEONE USE ALREDY EZE DOPE , IT WORKS OK?

IM STARTING COVERING A GUILLOWS ARROW LC

AND I WANT TO TRIED

Wildpig · Post by **Wildpig** » Fri Jul 12, 2013 12:10 pm

I have not used EZE dope but, here is a link to video of someone covering a Guillow Skyraider using that product.
http://www.youtube.com/watch?v=I3SCSrhYrhw

jonathanmanopla · Post by **jonathanmanopla** » Fri Jul 12, 2013 12:23 pm

Wildpig wrote:I have not used EZE dope but, here is a link to video of someone covering a Guillow Skyraider using that product.
http://www.youtube.com/watch?v=I3SCSrhYrhw

thanks alredy saw the video

i want someone that use alredy , because on the Video its not look very well

paul · Post by **paul** » Fri Jul 12, 2013 1:01 pm

I have used EZE Dope once, and it gave the tissue a mottled effect. So I went back to "normal" dope and thinners.
I am not blaming the product totally for the mottled effect, as there are more underlining reasons why this happened.
If I where to use it again I would certainly try it on a test piece first

limey · Post by **limey** » Fri Jul 12, 2013 1:54 pm

Hi Jonathan I have used easydope but it was from a source in the UK . It was my first build for 40 years so I have tried lots of new materials.I found it easy to use and did get reasonable results but as the other guys have said try it on a test piece first hardly any odour so it is female frendly!!!!!!you can see my build on FIRST BUILD FOR 40YEARS. Good luck Lime.

Tabitha64 · Post by **Tabitha64** » Fri Jul 12, 2013 6:46 pm

I have found that if you use glue stick (I prefer purple that drys clear) to place tissue in place, then spray with water or rubbing alcohol. Allow to dry. Then apply Eze dope. I got the result I was looking for. Good luck. Tabitha

jonathanmanopla · Post by **jonathanmanopla** » Sat Jul 13, 2013 10:04 pm

i Let you the Picture of my Guillows Arrow just Finished , tomorrow test Flight

i Use Esaki Tissue
and Uhu Stick
after i sprayed with water and for finish use KRYLON LACQUER CLEAR
HOPE IT FLY WELL

Wildpig · Post by **Wildpig** » Sat Jul 13, 2013 11:25 pm

Nice looking airplane model you have!

Should fly very nicely.

Be sure to make test glides and adjust the tail surfaces to trim the model.
Here is something that might help:
http://balsamodels.com/phpBB/viewtopic. ... t=trimming

Also, you could search this forum for topics on trimming.

jonathanmanopla · Post by **jonathanmanopla** » Mon Jul 15, 2013 11:20 am

Wildpig wrote:Nice looking airplane model you have!

Should fly very nicely.

Be sure to make test glides and adjust the tail surfaces to trim the model.
Here is something that might help:
http://balsamodels.com/phpBB/viewtopic. ... t=trimming

Also, you could search this forum for topics on trimming.

THANKS I FLY IT YESTERDAY ITS FLY VERY WELL AND STRAIGHT

zoltron55 · Post by **zoltron55** » Sat Jul 27, 2013 6:36 pm

I put a little right turn on my stuff, then it doesn't get too far away

jonathanmanopla · Post by **jonathanmanopla** » Mon Sep 23, 2013 8:14 am

Yesterday Converted my Arrow to RC

heres the Pictures
hope to fly it on thursday i see hows goin

i Use the Electronic of a Eflite 4site

Guillow's Model Builders Forum

Guillows Arrow RC CONVERSION

Guillows Arrow RC CONVERSION

Re: How has Tried EZE DOPE

Re: How has Tried EZE DOPE

Re: How has Tried EZE DOPE

Re: How has Tried EZE DOPE

Re: How has Tried EZE DOPE

Re: How has Tried EZE DOPE

Re: How has Tried EZE DOPE

Re: How has Tried EZE DOPE

Re: Guillows Arrow Finished

Re: Guillows Arrow Finished